Якісні запчастини до мотоциклу Triumph

• 12 Volt and 6 Volt
• Lead acid, AGM and Gel batteries
• Quick mode change button on front face
• 1 Amp
• Battery Range 1.3-60Ah
• Cable Length 1m (To quick connect plug), 1.1m (Including clamps/eyelet cable)
• Trickle charger
• Quick release plug with cover
• Wall plug compact design
• Weight 0.58Kg

• 12 Volt and 6 Volt
• Lead acid, AGM, Gel and Lithium batteries
• Quick mode change button on front face
• 2 Amp
• Battery Range 1.3-60Ah
• Cable Length 1m (To quick connect plug), 1.1m (Including clamps/eyelet cable)
• Trickle charger
• Quick release plug with cover
• Wall plug compact design
• Weight 0.58Kg

Kit Contains - 2 Ball Bearings (25x47x12)

NO SEALS IN THIS KIT

Dimensions:
M8 x 30mm
10mm shoulder
6mm Allen
16mm Diameter Head
1.25mm Thread Pitch

Dimensions:
M8 x 30mm
10mm shoulder
6mm Allen
16mm Diameter Head
1.25mm Thread Pitch

Kit For Single Caliper Contains:

• 2 wiper seals
• 2 dust seals
• 2 shaft boots
• 1 stainless steel bleed nipple
• 1 bleed nipple cover
• 2 copper washers
• 1 sachet of red rubber grease

Kit Contains:

• 2 stainless steel pistons
• 2 wiper seals
• 2 dust seals
• 2 shaft boots
• 1 stainless steel bleed nipple
• 1 bleed nipple cover
• 2 copper washers
• 1 sachet of red rubber grease

High Corrosion Resistance
- Yellow Zinc Plated
8mm 1.25

High Corrosion Resistance
- Yellow Zinc Plated
8mm 1.25

For Hoses requiring special fittings the banjos can only be supplied in silver.
Made to order, usually 24 hours to manufacture
This is a single line,
supplied with black heat shrink over the end of the hose

For Hoses requiring special fittings the banjos can only be supplied in silver.
Made to order usually 24 hours to manufacture
Two lines in a Kit
Supplied with black heat shrink over the end of the hose

For Hoses requiring special fittings the banjos can only be supplied in silver.
Made to order, usually 24 hours to manufacture
Two lines in a Kit, Supplied with black heat shrink over the end of the hose
The longer line goes from the Master Cylinder to one of the Calipers,
then Connects both lines using the Double Banjo Bolt and washers on the Caliper.
Run the shorter line over the Mudguard to reach the other Caliper.

This link is compatible with DID ZVM-X chains only.
For DID ZVM-2 chains please see our chain links section.

Automatic Chain Lubrication System for Motorcycles.
Eliminates chain cleaning, suits all types of chain including O ring.
Can be used for on and off road and gives between 2 to 7 times chain life.
Only suitable for motorcycles with a vacuum take-off point.
Motorcycles which don't have this feature will need to be fitted with the E-System instead.

White Lubricant.
Fully synthetic clear formula has absolute resistance against fling-off and is completely waterproof.
Compatible with o-rings, x-rings and z-rings.

Maxxis all new Supermaxx ST Sport Touring Tyre
The Supermaxx ST features an advanced V-groove tread pattern
with an intensive groove design to expel standing water from the contact patch,
maintaining consistent handling characteristics in varied road conditions wet or dry.
Compared to Maxxis long-standing Supermaxx, the Supermaxx ST larger contact area,
stiffer carcass and improved tread compound deliver:
21% increase in camber grip
40% increase in footprint at 40 degrees of lean angle
15% increase in wet grip
20% increase in mileage performance

Dimensions :
Interior diameter = 42 mm
Exterior diameter = 115 mm
Thickness = 21 mm
Number of wires = 3
Number of plugs = 1
Number of terminals = 3
Harness length stator to grommet = 110 mm
Harness length grommet to plug = 600 mm

Key colour may vary between blue and black

**** PLEASE READ THE INSTRUCTIONS FIRST *****
520 Chain to 530 Chain soft rivet link only,
old rivet heads need to be ground off
with an angle grinder before they can be extracted.

Fits oil filters F306,F303,K301,HF204,HF303,HF148
Please check there is room to fit.
This tool is unsuitable for some filter fitments. Example Honda V Twins.
Oil Filter Wrench 65mm
Uses 3/8 Wrench Adaptor

Consists of:
1x 12-point, S 28 mm, for Ducati
1x 6-point, size 30 mm, for Ducati
1x 6/12-Kant, width 41 mm, 2 to 1, to loosen the rear wheel
1x 6/12-Kant, SW 46 mm, 2 to 1, to loosen the rear wheel
with single-sided swingarm, as Ducati, Triumph swingarm
1x 6-point AF 28 mm, 1 x 12-point AF 55 mm, 2 to 1, for Ducati
3 O-rings